-
What to do if the wheel is unsteady?
-
The bore diameter and the fixing pin diameter are not the same. – Choose a suitable bore size or use a seal ring.
-
The flange is worn out. – It should be cleaned or replaced.
-
A defective support element can also cause the wheel to oscillate. – Change the machine or support element.
-
-
Cutting surface is blue. What to do?
-
Insufficient power of the angle grinder. – Use a more powerful angle grinder.
-
Too wide wheel for this type of processing. – Try to use thinner wheel.
-
Long cutting times. – Try increasing the force or speed of pressure.
-
Too hard wheel. – It is recommended to choose a softer tool.
-
Large cross-section of material for a given wheel diameter. – Handle material with a smaller diameter or try using a plate.
-
-
How to prevent bore breakage?
-
Improper use of equipment. – When operating, it is necessary to reduce lateral pressure.
-
STOP! The cutting wheel is used for stripping. – ATTENTION! Do not use a cutting wheel for stripping.
-
Different mounting flanges. – Use flanges of the same diameter.
-
-
How to avoid an oblique cut?
-
The work piece for processing is incorrectly fixed. – Try fixing the material closer to the cutting site.
-
The wheel is completely worn out and is not suitable for use. "Just replace it."
-
Check the pressure. – If the pressure is too high, reduce it.
-
Insufficient thickness of the wheel for this type of treatment. – Choose a wheel of greater thickness.
-
-
Quick wear of the wheel – there's a way out
-
Too many rotations. – It is worth reducing the pressure force or using more powerful equipment.
-
A small circumferential speed. – Make the cutting speed higher.
-
REMEMBER! If the surface of the cut is white, the hardness of the wheel is insufficient. – Choose a harder wheel.
-
-
The wheel breaks, what to do?
-
Do you operate the angle grinder correctly? – IMPORTANT! Avoid side pressure on the wheel.
-
Material for processing is not fixed correctly. – Place the work piece closer to the work area.
-
STOP! As mentioned above, do not use a cutting wheel for grinding.
-
The flange is not selected correctly: it has an insufficient diameter. – Use a flange of the appropriate diameter.
-
-
What to do if the periphery of the wheel is worn out?
-
CHECK! Perhaps the wheel was burned around the edge. – Reduce the force of pressure or choose a softer bunch.
-
The work piece is not properly fixed. – Just fix it closer to the cutting site.
-
-
What are the reasons that the circle is often clogged?
-
Too little force of pressure. – Try to increase it.
-
Blocking is possible during processing non-ferrous metals. – You can choose a soft bunch or a wheel with a softer bunch, but it's better to use a special wheel for processing non-ferrous metals.
-
Too hard a binder of a wheel. – Choose a softer one.
-
-
Grinding is ineffective, what to do?
-
The reason for this may be the insufficient power of the grinder. – Use more powerful equipment.
-
A small force of pressure. – It's worth to increase
-
The contact surface is glistening: the binder of the wheel is stiff. – It is recommended to choose a softer one.
-
-
What to do if the wheel moves ineffective?
-
IMPORTANT! The mount is not centered. – Try to correctly adjust the diameter of the hole and the clamping element.
-
The mounting spindle is worn out. – It is necessary to replace the grinder with a new one.
-
The wheel has bends. – Use another wheel.
-
The flange is dirty or blocked. – You need to clean or replace it.
-
-
What to do if the wheel wears out quickly?
-
Check the pressure. Maybe it's too big. – If necessary reduce the pressure.
-
Insufficient machine power. – Choose powerful equipment.
-
Does the speed of rotation decrease too fast? Also, try to reduce the pressure.
-
Soft binder of a wheel. – Choose a firmer one.
-
-
What if the edge of the circle breaks off and the periphery is not round?
-
CHECK! The machining angle may be too flat. – The angle must be at least 15.
-
Strong force of pressure. – Try to reduce it.
-
-
What to do if the wheel is unsteady?
-
The bore diameter and the fixing pin diameter are not the same. – Choose a suitable bore size or use a seal ring.
-
The flange is worn out. – It should be cleaned or replaced.
-
A defective support element can also cause the wheel to oscillate. – Change the machine or support element.
-
-
Cutting surface is blue. What to do?
-
Insufficient power of the angle grinder. – Use a more powerful angle grinder.
-
Too wide wheel for this type of processing. – Try to use thinner wheel.
-
Long cutting times. – Try increasing the force or speed of pressure.
-
Too hard wheel. – It is recommended to choose a softer tool.
-
Large cross-section of material for a given wheel diameter. – Handle material with a smaller diameter or try using a plate.
-
-
How to prevent bore breakage?
-
Improper use of equipment. – When operating, it is necessary to reduce lateral pressure.
-
STOP! The cutting wheel is used for stripping. – ATTENTION! Do not use a cutting wheel for stripping.
-
Different mounting flanges. – Use flanges of the same diameter.
-
-
How to avoid an oblique cut?
-
The work piece for processing is incorrectly fixed. – Try fixing the material closer to the cutting site.
-
The wheel is completely worn out and is not suitable for use. "Just replace it."
-
Check the pressure. – If the pressure is too high, reduce it.
-
Insufficient thickness of the wheel for this type of treatment. – Choose a wheel of greater thickness.
-
-
Quick wear of the wheel – there's a way out
-
Too many rotations. – It is worth reducing the pressure force or using more powerful equipment.
-
A small circumferential speed. – Make the cutting speed higher.
-
REMEMBER! If the surface of the cut is white, the hardness of the wheel is insufficient. – Choose a harder wheel.
-
-
The wheel breaks, what to do?
-
Do you operate the angle grinder correctly? – IMPORTANT! Avoid side pressure on the wheel.
-
Material for processing is not fixed correctly. – Place the work piece closer to the work area.
-
STOP! As mentioned above, do not use a cutting wheel for grinding.
-
The flange is not selected correctly: it has an insufficient diameter. – Use a flange of the appropriate diameter.
-
-
What to do if the periphery of the wheel is worn out?
-
CHECK! Perhaps the wheel was burned around the edge. – Reduce the force of pressure or choose a softer bunch.
-
The work piece is not properly fixed. – Just fix it closer to the cutting site.
-
-
What are the reasons that the circle is often clogged?
-
Too little force of pressure. – Try to increase it.
-
Blocking is possible during processing non-ferrous metals. – You can choose a soft bunch or a wheel with a softer bunch, but it's better to use a special wheel for processing non-ferrous metals.
-
Too hard a binder of a wheel. – Choose a softer one.
-
-
Grinding is ineffective, what to do?
-
The reason for this may be the insufficient power of the grinder. – Use more powerful equipment.
-
A small force of pressure. – It's worth to increase
-
The contact surface is glistening: the binder of the wheel is stiff. – It is recommended to choose a softer one.
-
-
What to do if the wheel moves ineffective?
-
IMPORTANT! The mount is not centered. – Try to correctly adjust the diameter of the hole and the clamping element.
-
The mounting spindle is worn out. – It is necessary to replace the grinder with a new one.
-
The wheel has bends. – Use another wheel.
-
The flange is dirty or blocked. – You need to clean or replace it.
-
-
What to do if the wheel wears out quickly?
-
Check the pressure. Maybe it's too big. – If necessary reduce the pressure.
-
Insufficient machine power. – Choose powerful equipment.
-
Does the speed of rotation decrease too fast? Also, try to reduce the pressure.
-
Soft binder of a wheel. – Choose a firmer one.
-
-
What if the edge of the circle breaks off and the periphery is not round?
-
CHECK! The machining angle may be too flat. – The angle must be at least 15.
-
Strong force of pressure. – Try to reduce it.
-